Soundproof Your Studio podcast

He Built a Soundproof Drum Studio With No Plans. Here's What Went Wrong

0:00
38:52
Reculer de 15 secondes
Avancer de 15 secondes

SOUND ISOLATION DESIGN · SPYS DESIGNS

The Client Should Not Be the Go-Between: Lessons From a Drum Room Built Without Plans

Jeremy is a composer, producer, and drummer in Washington state. Last year he built a single room for mixing, tracking live drums, and rehearsing with his band as part of a new custom home. He was a consulting client of mine from the period when I offered consulting without plan sets, which means he built this room without one. He was generous enough to sit down and walk me through everything on camera, including what went wrong. This article pulls out what I think matters most for anyone planning a high-performance room.

Why he needed the room in the first place

Before this room, Jeremy lived in a townhouse with thin walls. He worked in headphones because he could not be loud, he could hear his neighbors, and his acoustic drums sat in storage for four years. When he and his wife built a new home, the studio was a priority from the start. What he wanted is what most of my clients want. He wanted the freedom to turn up when the work calls for it and to stop thinking about who might be listening.

What we built, and what it actually delivers

The room sits on the slab, with a living room directly above it. The walls are a double wall construction with an air gap between two independent leaves. The ceiling is hung on resilient clips with hat channel and heavy layers of drywall. The entry is a pair of doors, one high-performance isolation door and one budget door with glass, which gives a few extra decibels of reduction for a small amount of money. Fresh air comes through baffle boxes connected to an energy recovery ventilator in an adjacent utility room.

Here is how he describes the result. With the kit at full volume, it sounds like a miniature drum kit being played somewhere in the house, and his wife can watch television while it happens. When he mixes loud or plays a guitar amp, you basically cannot hear it outside the door. At the property line he says you would have to stand a foot or two from the siding to hear anything.

What we do on most residential builds is turn the volume knob down. That is a real result, and it is hard to achieve.

I want to be honest about that framing, because it is the most important expectation to set. Sound isolation on a project like this is not silence. Drums are the loudest thing in most homes, and the wall without a door was never going to be quieter than the wall with one at the same level of treatment. Jeremy said it was louder on the drum side, and that is physics. What he got is a room where the volume comes down enough that the people in his house and his neighbors are not bothered, and that is the outcome we designed for.

The floor question

One detail worth pausing on. Jeremy did not float his concrete slab, and the room performs very well. I know that surprises people, and AI tools in particular love to insist a studio floor must be floated. In his case the room sits on a slab on grade and the real work was done by the isolation of the walls and ceiling. That does not mean a floating floor is never needed. A room over a framed floor, or a project with heavy low frequency content next to living space, is a different problem. Every project has to be evaluated on its own conditions, which is the whole point of design.

Where it got hard: the client became the translator

The build was not the hard part. The hard part was communication. Jeremy's builder was excellent, but he had never built a room like this, and he came in with good intentions and a few assumptions picked up online. Jeremy was caught in the middle. He was learning from me, then going to the builder, and trying to carry the language of two different worlds back and forth without being fluent in either.

I'm the go between.

Over a build that ran about fourteen months, the budget grew, as it does. Lumber and material prices moved, and the studio had no contingency the way the house did, because nobody could say in advance what a specialty room like his would cost. Jeremy ended up doing much of the finishing himself, including tile and electrical trim, because the money was gone and the room was his workspace. He told me he has never learned so much in a year, and I believe him. But no client should have to learn a trade to get the room they hired a designer for.

Two moments show why this matters. The electricians connected the studio circuit back into the rest of the house even though the plan called for it to be separate, so Jeremy rewired part of it after the fact. And the first layout had the plumbing stack for the house running through a studio wall. Both are the kind of conflict that a coordinated set of drawings catches before anyone picks up a tool.

The one thing he would change

When I asked what he would redo, Jeremy did not name the budget or the builder. He said he would move the door about eight inches. Because of where his desk sits, the door location left him without an absorption panel at one of his first reflection points, and he notices it every day. It is a small issue in a good room. It is also a clean example of why we work out reflection points, door swings, and ceiling cloud locations on paper before anything is framed. When he moved the door late in the process, the acoustic layout did not move with it.

What this means for your project

Jeremy's room works, and he is very happy with it. The lesson I take from his build is about process more than product. The wall and ceiling details were sound. What cost him time, money, and sleep was the gap between the designer and the people holding the tools. That is the reason we moved from consulting only to full construction plan sets with a checklist that a site manager can verify and photograph for us. The plans carry the language so the client does not have to.

The biggest lesson: the homeowner shouldn't have to be the communication system holding a specialized construction project together.

Learn more about Jeremy:
https://jeremykdavid.com

Listen to Summer Eyes:
https://summereyesband.com

Planning a sound-isolated room?

If you are planning a room that has to perform at this level, the details are not optional considerations. They are the difference between a room that works and one that does not. That is the standard we hold at SPYS Designs.

NEXT STEP: Start with a Sound Isolation Site Assessment. Tell us about your room, your structure, and your goals so we can tell you what it will take to reach them.

D'autres épisodes de "Soundproof Your Studio"